How do I replace the drain pump on a Whirlpool front load washer?

VIDEO

Furthermore, where is the drain pump on a front load washer?

Open the drain pump filter cover at the bottom of the washer front panel. Remove the screw that secures the plastic pump housing to the frame of the washer. Remove the plastic pump housing. Remove the mounting screw from bottom of the front panel.

Likewise, how do I know if my washing machine drain pump is bad? If the motor and pump is running but no water is draining out then most likely the 3363394 pump is bad. One thing you can try first is to lower the drain hose over a shallow pan and see if the water in the tub will drain by gravity. If not then there may be a sock or other obstruction blocking the pump.

Also, how do you get to the drain pump on a Whirlpool Duet washer?

The location of the drain pump filter in a Whirlpool Duet washer is accessible through the lower access panel below the washer door.

Unplug your Whirlpool Duet washer power cord from the wall outlet.
Find the screws securing the lower access panel to the washer cabinet.
Remove the screws with a 1/4-inch nut driver.

How much is a drain pump for a washing machine?

The most important part is a new washer pump. It can cost as little as $10 or as much as $75 or more. However, most homeowners pay between $25-$40 for a new pump.

Where is the pump on my Whirlpool washing machine?

Locate the pump underneath the bottom of the washing machine. The pump is easy to locate because it has two hoses attached to it.

Why is my washing machine not draining all the way?

If the washer won't drain there might be a clogged pump or hose. It's common for small socks or other small clothing items to get into the water drain system and clog the hose leading to the pump or the pump itself. Cleaned the filter and the machine still will not drain. So that must mean the hose or pump is clogged.

Where is the filter on Whirlpool front load washer?

The filter on a Whirlpool Duet is located under the front kick plate. A washer filter collects lint that falls from clothes during the washing process.

How do you open a Whirlpool front load washer?

Hold down the "Control Lock" button on your Whirlpool washer for three seconds at the end of the washing cycle. Listen, and when you hear the unlatching sound, the door should open.

How do I fix my Whirlpool Duet washer?

Unplug the washer for 30 seconds to attempt to reset the Duet washer control. if your fill hoses have a flood stop check valve turn the water off, disconnect the hoses and run a little water into a bucket. Then reconnect the hoses to your washer and do a Duet Washer Quick Diagnostic Test.

Where is the model number on a Whirlpool washer?

Where do I find the model number on a Whirlpool washer? ANSWER Hello, If you raise the lid and squat down and look under the bottom edge of the opened lid you should see the units' I.D. tag. The top number is the model and the bottom number is the serial number.

How do you drain a Whirlpool washing machine?

Start by unplugging the machine and emptying the water. Bail the water out of the tub, or you can drain the tub using gravity by placing the washer drain hose on the floor near the drain or in a bucket. Clamp the hose to prevent any remaining water from running out.

Why won't my front load washer drain?

If the washer won't drain there might be a clogged pump or hose. It's common for small socks or other small clothing items to get into the water drain system and clog the hose leading to the pump or the pump itself. If the washer won't drain the lid switch assembly might be defective. This is a very common problem.

How often should you drain your front load washer?

This should be done about every two weeks. If the drain pump filter gets clogged with debris, the water flow will slow down, and fill up with stinky water over time.

How can I unclog my washing machine?

To clear a clog from a washing machine, try unhooking the drain pipe and pouring hot water down the drain to release the soap and scum. For stubborn clogs, push a plumbing snake down the drain. As it goes down, turn the handle clockwise anytime you feel a clog, which will grab the debris and allow you to pull it out.

Why isn't my washer spinning the clothes dry?

When your washer will not spin dry your clothes, the debris filter or coin trap may be blocked. Your washer has a filtering device down and near the pump called a drain filter or a coin trap. This filter grabs all foreign objects that go down and into the drain.

Why is my Whirlpool front load washer not draining?

If your Whirlpool washer stops draining the drain pump is likely clogged up with some sort of debris. When these washers stop draining the control panel will normally give you an error code. The error code is normally F02. This means the drain pump is trying to run but the water is not draining.